View RWP06040-G1_4953868.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Wideband Power Amplifier
Product Features
GaN on SiC Broadband High Power Amplifier 500 to 1000MHz Operation Bandwidth Small Signal Gain 40dB min 40W Typical , P3dB
RWP06040-G1
UHF/Military
Application
Package : DP-75
Description
The power amplifier module is specifically designed for Military markets. Operating frequency range is from 500MHz to 1000MHz. Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband performance is already applied. Improved thermal handling by patented technology.
Typical Specifications
No 1 2 3 4 5 Bandwidth Small Signal Gain Gain Variation vs Temperature Gain Variation vs Frequency P3dB OIP3 @ Po = +33dBm (1MHz Tone spacing, CW 2-Tone) Input Return Loss Output Return Loss 2nd Harmonic suppression Supply Voltage Quiescent Current consumption Current Consumption On/Off Switching Time Shut Down or Switch On/Off TTL Voltage CW 1-tone @ Po = +46dBm On : TTL "Low" Off : TTL "High"(300mA@Disable) On : TTL "Low"(Enable) Off : TTL "High" CW 1-tone @Po = +30dBm, Freq 500MHz Vcc(=Vds) 500MHz to 700MHz 700MHz to 1000MHz 500MHz to 1000MHz -20C to 60C Item Conditions
VCC = +28V; T = 25; ZS = ZL = 50 Min 500 40 -2 1 44 46 48 45 47 46 -5 -12 -35 27.5 28 3 4.5 3 0 2.5 5 -3 -7 -30 30 3.5 5 5 0.5 5.5 42 Typ Max 1000 44 +2 2 Unit MHz dB dB dBpp dBm
6 7 8 9 10 11 12 13
dBm dB dB dBc V A A uS
14
V
Tel : 82-31-250-5078 www.rfhic.com/contact
All specifications may change without notice. Version 1.0
Wideband Power Amplifier
Environmental Characteristics
No 1 2 3 Operating Temperature Storage Temperature Vibration Item
RWP06040-G1
Min -20 -40
Typ
Max +60 +105
Unit C C
MIL-STD-810G Method 514.6 ANNEX C
Absolute Maximum Ratings
No 1 2 3 4 Input RF Power Supply Voltage Load Mismatch Value Item Operating Flange Temperature Rating +85 +12 +30 3 : 1 @ all load phase Unit C dBm V
* Input Signal Condition : CW 1-Tone
Ordering Information
No 1 2 RWP06040-G1 RWP06040-GH Part Number Pallet Module assembled with RWP06040-G1 Package
* RWP06040-GH is a SMA connectorized housing version of RWP06040-G1. Electrical parameters are all same as RWP06040-G1. For more information, please contact RFHIC.
Tel : 82-31-250-5078 www.rfhic.com/contact
All specifications may change without notice. Version 1.0
Wideband Power Amplifier
RWP06040-G1 Typical Performance @ 25
Frequency (MHz) 500 600 700 800 900 1000 P1dB (dBm) 42.6 42.9 43.1 44.3 44.0 46.3 P3dB (dBm) 45.4 45.6 46.2 47.7 47.0 47.3 Current@P1dB (A) 2.99 3.80 3.33 3.61 3.41 3.30
RWP06040-G1
Current@P3dB (A) 3.80 4.13 4.74 5.24 4.85 3.51
2nd Harm @30dBm(dBc) -35.6 -35.96 -36.58 -44.92 -58.74 -77.78
OIP3 (30dBm/Tone) (dBm) 52.7 53.3 53.4 53.4 52.7 51.2
P3dB
2nd Harmonics
OIP3
Power Gain @ Pin=8dBm
Tel : 82-31-250-5078 www.rfhic.com/contact
All specifications may change without notice. Version 1.0
Wideband Power Amplifier
Precautions
RWP06040-G1
1. This product is designed to be used for broadband amplification. Heat generation is higher when there is no RF signal in the device. Therefore, the worst case scenario is when there is no RF signal, and the amplifier is "on" with current draw. The temperature must be calculated properly. Case temperature must maintain below 85C. 2. Thermal Grease or Metal Thermal Interface Materials are recommended for heat dissipation. An example would be spreading thermal grease on the bottom of the device.
Package Dimensions (Type: DP-75)
(Unit : mm/[inch], Tolerance : 0.2/[.008])
70 [2.756] 60 [2.362] 20 [.787] 20 [.787]
70 [2.756] 60 [2.362]
38 [1.496] 50.8 [2] 45 [1.772]
1.5 [.059] 15.6 [.616] 6.2 [.245] 6.9 [.273] 7.3 [.288] 7.3 [.286] 6.9 [.273]
38 [1.496] 50.8 [2]
'A'
C
1 [.039]
3.8 [.15]
5 [.197]
4 [.156]
2.5 [.098]
17.1 [.673]
4.1 [.161]
4.5 [.177]
2 [.079]
1.5 [.059]
How to connect the amplifier to a target PCB
Method- (with Pin) Method- (without Pin) - If you cut out the pin
Tel : 82-31-250-5078 www.rfhic.com/contact
All specifications may change without notice. Version 1.0
Wideband Power Amplifier
Pin Description
Pin No 1 2 3 4 5 6 RF IN Vcc (+28V) Shut Down (+5V) Switch ON/OFF GND RF OUT Port Name
RWP06040-G1
Function RF Input DC Supply Shut Down @ TTL High, Enable @ TTL Low Disable @ TTL High (Switch Status : Off) Ground RF Output
* Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket) * Recommended Screw Torque : 8.0kgf.cm1 using SEMS M3 10mm Bolt
Note :
RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC's liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC.
Tel : 82-31-250-5078 www.rfhic.com/contact
All specifications may change without notice. Version 1.0

▲Up To Search▲

Price & Availability of RWP06040-G1

	To Download RWP06040-G1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .